Right Crete Thin Repair
Right Crete Thin Repair

 

  Right Crete Thin Repair
SDSspacerPDF

 

DESCRIPTION
RIGHT CRETE THIN REPAIR is a multipurpose repair and resurfacing compound for applications from a featheredge to 1 inch. RIGHT CRETE THIN REPAIR has an initial set in 30 to 40 minutes, final set in 1 hour and cures in 24 hours.

USE AND APPLICATIONS
• Repair spalls
• Driveways
• Surface leveler
• Honeycombs
• Sidewalks
• Bug holes

FEATURES AND BENEFITS
• Polymer in the bag, just add water
• Long working time
• Pleasing light gray color
• Tenacious bond
• Finely graded sands for easy featheredging

PACKAGING
• 50 lb Bag

Coverage Rate
• One (1) 50 lb bag will yield approximately .40 cubic feet

APPEARANCE
• Light gray option
• Concrete gray option

SHELF LIFE
• Minimum of one (1) year stored in dry protected storage

DIRECTIONS FOR USE
Proper surface prep for all horizontal repair materials is critical. Surface must be clean from dirt, grease, oils and other contaminants. Loose concrete must be removed until a sound concrete substrate is exposed. Pre wet the area to a surface saturated dry (SSD) condition.

MIXING
RIGHT CRETE THIN REPAIR will require 3.5 to 4 quarts of water per 50 lb bag. Small quantities may be mixed with a margin trowel, larger quantities with a jiffy mixer. Mix to a lump free consistency. Do not re-temper RIGHT CRETE THIN REPAIR.

APPLICATION
Pre-wet the surface, trowel the product firmly into place eliminating any air pockets. For surface leveling, use a screed before troweling. Working time is 30 minutes.

CLEAN UP
Clean tools with water immediately after use.

RESTRICTIONS
Do not re-temper.
Do not exceed 4 quarts of water per bag.
Do not apply under 40 degrees.
Do not use as a topping or underlayment see Right Patch 2C.
Do add powder to the water.
Do use from featheredge to 1 inch per lift.

 

 

 
 

MATERIAL PROPERTIES

ASTM C109
Compressive Strength
  7 Day 3350 psi
  28 Day 5100 psi
ASTM C190
Compressive Strength
  7 Day Avg. 245 psi
  28 Day Avg. 410 psi
ASTM C266
Set Time, Gilmore
  Inital Set 30-40 Minutes
  Final Set 1-2 Hours
ASTM C348
Flexural Strength
  7 Day 630 psi
  28 Day 725 psi
ASTM C157
Shrinkage, Pct.
  7 Day Avg. 0.084%
  28 Day Avg. 0.128%

TECHNICAL SERVICE
For conditions not specified, application procedures not noted, contact: Right Pointe, LLC (888) 755-5700.

LIMITED WARRANTY
Every reasonable effort is made to apply Right Pointe, LLC exacting standards both in the manufacture of our products and in the information which we issue concerning these products and their use. We warrant our products to be of good quality and will replace or, at our election, refund the purchase price of any products proved defective. Satisfactory results depend not only upon quality products, but also upon many factors beyond our control. Therefore, except for such replacement or refund, Right Pointe, LLC MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, RESPECTING ITS PRODUCTS, and Right Pointe, LLC shall have no other liability with respect thereto. Any claim regarding product defect must be received in writing within one (1) year from the date of shipment. No claim will be considered without such written notice or after the specified time interval. User shall determine the suitability of the products for the intended use and assume all risks and liability in connection therewith. Any authorized change in the printed recommendations concerning the use of our products must bear the signature of the Right Pointe, LLC Technical Manager.

 

CLICK ON PHOTO TO ENLARGE
1

   

ABOUT US

 

OUR PRODUCTS
Expansion Joints and Plastics
Waterproofing

Joint Sealants
Chemical Liquids
Cementitous Products
Roofing

 

CONTACT US

 

FEATURED PRODUCTS

 

CAREERS

 
© 2017-2019 All Rights Reserved Right Pointe, LLC.