#5078 Class B
#5078 Class B
No. JTS-072

 

  #5078 Class B
SDSspacerPDF

 

DESCRIPTION
#5078 CLASS B is a mixture of asphalt, plasticizer, synthetic polymer, and reclaimed tire rubber. Our most economical material is a hot applied, one part sealant that provides superior results over roofing and straight paving grade asphalts.
• Good bonding characteristics
• Weather resistant
• Passes multiple freeze and thaw cycles

SPECIFICATIONS
• TX DOT Rubber Asphalt Crack Sealer Class B

TYPICAL PROPERTIES
Minimum application temperature............................................ 380° F (193° C)
Maximum heating temperature...................................................400° F (204° C)
Cone penetration, 77° F (25° C) ..................................................................30-50
Cone penetration, 32° F (0° C), 200 g 60 sec. .......................................12 min
Softening point (ASTM D36)...................................................205° F (96° C) min
Flash point, modified C.O.C. ..............................................400° F (204° C) min
Virgin rubber polymer, % by wt. ................................................................2% min
Granulated vulcanized rubber, % by wt. .................................................13-17%
Bond @ 20° F (-7° C), 50% ext. ....................................................Pass 3 cycles

USE AND APPLICATIONS
#5078 CLASS B is recommended for sealing of joints and cracks in concrete and asphaltic pavements and parking lots. It is designed for use in sealing expansion and contraction joints as well as random cracks.
• Roadways
• Highway shoulders

FEATURES AND BENEFITS
• Compound for concrete and asphaltic pavements
• Actually prolongs the pavement service life
• Seals cracks and joints from water penetration

EQUIPMENT
Use an agitated oil-jacketed unit that has separate temperature gauges for both the sealant and the heat transfer fluid. Take the 30 lb plastic bag of sealant and load into the kettle one at a time. Melt only enough material for the day's activities. Once melted, additional material can be added as needed. Material can be safely reheated within the sealants service life.

NOTE: Prolonged heating of the sealant above the maximum safe heating temperature may cause it to gel in the kettle.

PREPARATION
To facilitate proper adhesion, the joint or crack should be dry and clear of any dirt, dust or other contaminates. Substrate and ambient temperatures must be 40º F or above. Proper sizing of the joint will cause the maximum extension/compression to not exceed 50% of the width. Joints or random cracks of 1/4" or less are difficult to properly clean prior to applying the sealant.

SERVICE LIFE
The service life (pot-life) at application temperatures is approximately 12 hours. Adding fresh material to the melter as sealant is being used will extend the service life. Material that has been overheated can thicken and gel in the melter. Any material that has exceeded the service life should be removed from the melter and discarded.

 


 
 

COVERAGE

Width
Depth
Pounds/100 Lineal Feet
3/8"
3/8"
6.9
3/8"
1/2"
9.3
1/2"
1/2"
12.3
1/2"
1"
24.7
3/4"
1/2"
18.6
3/4"
3/4"
27.8


PACKAGING

60# CARTON (2 SPLIT 30# CUBES)
36 CARTONS PER PALLET

35# CARTON
60 CARTONS PER PALLET

30# NO BOX TRI-BLOCK UNIT
65 UNITS PER PALLET


***********Patent Pending***********

TECHNICAL SERVICE
For conditions not specified, application procedures not noted, contact: Right Pointe, LLC. (888) 755-5700.

LIMITED WARRANTY
Every reasonable effort is made to apply Right Pointe, LLC. exacting standards both in the manufacture of our products and in the information which we issue concerning these products and their use. We warrant our products to be of good quality and will replace or, at our election, refund the purchase price of any products proved defective. Satisfactory results depend not only upon quality products, but also upon many factors beyond our control. Therefore, except for such replacement or refund, Right Pointe, LLC. MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, RESPECTING ITS PRODUCTS, and Right Pointe, LLC. shall have no other liability with respect thereto. Any claim regarding product defect must be received in writing within one (1) year from the date of shipment. No claim will be considered without such written notice or after the specified time interval. User shall determine the suitability of the products for the intended use and assume all risks and liability in connection therewith. Any authorized change in the printed recommendations concerning the use of our products must bear the signature of the Right Pointe, LLC. Technical Manager.


CLICK ON PHOTO TO ENLARGE
1

 
 

ABOUT US

 

OUR PRODUCTS
Expansion Joints and Plastics
Waterproofing

Joint Sealants
Chemical Liquids
Cementitous Products
Roofing

 

CONTACT US

 

FEATURED PRODUCTS

 
© 2015-2020 All Rights Reserved Right Pointe, LLC.